Premium o ring factory: Without the pressure pushing them apart the two seal faces would be in full contact, this is known as dry running and would lead to rapid seal failure. Without the process pressure (and the force of the springs) pushing the faces together the seal faces would separate too far, and allow fluid to leak out. Mechanical seal engineering focuses on increasing the longevity of the primary seal faces by ensuring a high quality of lubricating fluid, and by selecting appropriate seal face materials for the process being pumped. When we talk about leakage we are referring to visible leakage of the seal. This is because as detailed above, a very thin fluid film holds the two seal faces apart from each other. By maintaining a micro-gap a leak path is created making it impossible for a mechanical seal to be totally leak free. What we can say, however, is that unlike gland packing, the amount of leakage on a mechanical seal should be so low as to be visually undetectable. Find even more info on https://www.dmsseals.com/spring-seals.
Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications.
Because the system pressure is high, the temperature is high, and the wear is particularly serious, the seal is required to have good wear resistance. Low coefficient of friction: For construction machinery such as excavators and pump trucks, the hydraulic system pressure is high, the cylinder action speed is fast, and the wear of the seal is particularly serious. Therefore, the friction coefficient of the seal must be low, so that the seal has good wear resistance and suitable life.
The rotary seal from DMS SEALS is a dynamic sealing component that is installed between the rotating shaft and the stationary parts to seal the lubricating oil and prevent external dust and debris from entering the inside of the device. When selecting the material, we fully consider the working medium, working temperature and the adaptability of the lip when the shaft rotates at high speed. It has a remarkable sealing performance and can maintain a great sealing effect for a long time.
Rubber seals are a common type of basic component in sealing devices, and play a very important role in the contradiction between leakage and sealing. Using rubber seals is an important way to promote technological advancement and prevent and reduce environmental pollution. They are a class of rubber products that are widely used in sealing technology. Because rubber is a polymer material with valuable elasticity, a wide temperature range. It gives less stress in different media producing large deformation, which can provide contact pressure, compensate for leakage gap, and achieve the purpose of sealing.
Since the scraper seal is made of the special material, PTFE, it has an impurity immersion function. Therefore, when combined with the piston rod seal and the metal bushing, it can prevent damage to the piston rod and prevent the accumulation of oil pressure. It has a diameter range of 3-1600mm and a temperature range of -30°C + 200°C. The wiper scraper seal can operate at speeds of up to 5 m/s. It has high wear resistance, tear resistance, low-temperature resistance and good strength. Our wiper seals can be used in combination with piston seals and anti-wear rings to prevent oil in the cylinder from being mixed with foreign matter, which causes damage to the working seal. It is especially suitable for piston rods with a large diameter. Moreover, it has a wide range of applications, such as agricultural machinery, injection moulding machines, forklifts, cranes and so on.
The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.
Supplied in rolls or open loops. The open ring can be directly installed and used, but it must be cut when the roll is used, and the cutting length must be calculated in advance: there can only be one opening, the opening form is an oblique 45° opening, and the opening distance is about 3-15mm, or the diameter of the guide ring 3-5% of . Under normal circumstances, the openings are oblique openings. Straight openings or zigzag openings are rare and have specific uses and purposes. There are two purposes for the opening. The first is to facilitate installation. If it is not opened, it is an integral ring, which is difficult to install or impossible to install, so it must be opened. Secondly, the opening and a certain opening distance are reserved to facilitate the automatic coordination of volume changes. Otherwise, the movement may be stuck or the moving parts may be pulled due to the excessive expansion of the guide belt under certain conditions. Coiled ones are relatively cheap, and the same coil can be used to make guide rings of different sizes. Read extra details on https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.