Quality double side planer factory: The most common application involves gluing a coating (veneer, laminate, composite, PVC etc) onto a substratum (MDF, hardboard, plywood, hollow panels, blockwood etc). The basic configuration of the pressing line is comprised of a feed belt, an automatic press and a discharge deck. This configuration can be completed with numerous options, such as glue spreaders, polishers, automatic feeders, disk, roller or belt conveyors, automatic assembling stations, panel turners and stackers. Lines with various degrees of automation can be supplied right up to fully automatic lines that do not require direct intervention by the operator. Find extra information on double side planer.
Table and Belt Sander: The stationary belt sander uses a closed loop of paper that travels at speed around a pair of cylindrical drums. One drum is driven by an electric motor, the other is spring-loaded to maintain belt tension. Powered by the same motor, the stationery disk sander uses sanding disks that spin on a backing plate. On both the belt and disk sanders the work-piece is presented to the tool (the opposite is true of portable belt and hand held disk sanders which are presented to the work) on stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the work-piece during sanding. Re-saws are a type of band saw specifically designed to cut large sections of timber into smaller sections. Some re-saws can also be used to cut thick veneers making them a popular choice for the manufacturer of engineered wood flooring.
Up-acting machines typically apply hydraulic pressure from the centre of the lower beam which pushes the lower beam upwards into a fixed upper beam. Tonnage is applied to the centre of the lower beam in an upward fashion. The flex in the bend tends to be even from left to right. Hydraulics are used to push the lower beam up and gravity is used to return the lower beam down. A loss in power will result in the brake being in the open position. Since the lower beam does move during operation, feedback to the operator is given. Knowing the lower beam is moving can be a safety feature. Down-acting machines are preferred if staged bending is important. Staged bending is a valuable option that can significantly improve productivity while minimising setup time.
A jointer is used for planing straight edges and surfaces of boards. In practice, it performs the work of a hand planer and is capable of producing a true surface with sufficient accuracy and speed. In consists of a frame, table, feed rollers, revolving head fitted with two or three cutter knives. With the help of feed rolls, the plank is fed to the cutter head which removes the wooden chips as the board advances and makes its surface smooth and plane. By means of an adjustable fence, the jointer can also be used for angular and level cuts. A jointer is specified by the length of the cutting blade.
Probably the second most important of single woodworking machines in a carpentry shop is the circular saw. It can be used for ripping, cross cutting, mitering, beveling, rabbeting, and grooving. Although there are many types of circular saws such as universal saw, variety saw, bench saw, the basic working parts are common to all. Each has a flat surface or table upon which the work rests while being cut, a circular cutting blade, cut-off guide, and a ripping fence that acts as a guide while sawing along the grains of the wood. The circular saw usually has provisions for tilting the table upto an angle of 45° to enable the machine to cut at different angles required during mitering, levelling, etc. The size of a circular saw is determined by the diameter of the saw blade.
The wood is fixed between the headstock and tailstock of the lathe. The headstock houses the motor that spins the work-piece. The tailstock is adjustable, moving along the length of the bed to fit work-pieces of various lengths. Once the work-piece is locked in place, the tool rest is set into position. The spinning work-piece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in with the work-piece is fastened with screws to the face plate of the drive spindle, allows the woodworker to produce bowls and other hollow goods. Find even more info on v-holdmachinery.com.
Founded in 1996, V-HOLD have more than 20 years of professional four-sided plane production, to create China’s four-sided plane first brand and commits itself to provide the most secure, reliable, efficient, energy-saving, economical production equipment for the customers around the world. Nowadays, most of the products including 4-Side Moulder, Multiple Rip Saw, Multiple Rip Saw with Double Side Planner, and Automotive Floor Production Line have passed ISO9001: 2000 quality system.