Top rated woodworking machines provider: After 20 years development, V-HOLD has constructed strong hardware facilities and humanized management system by bringing in tens of brand-new large automotive precision CNC machine center from developed countries such as Japan, German, along with over 67,000m2 large modern workshop with complete facilities and production lines, V-HOLD has realized its high efficient production. Besides that, the cooperation with world famous management consulting firm and introduction of modern business administration system such as ERP, 6S have laid solid foundation to the development of V-HOLD. Thanks for the trust and support of our customer. V-HOLD will consistently stick to the belief that: Profession and concentration accomplish excellent brand ! Read additional info at four sided planer for sale.
The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.
A typical hydraulic down-acting press uses a pair of hydraulic cylinders, one on each end, to generate the tonnage required for the down stroke of the machine. Traditionally, these machines have a C or O frame profile design. With both types, when facing the front of the machine the hydraulic cylinders are located on the left and right hand side of the upper beam. Since the upper beam is being pushed down and up with hydraulic power, the upper beam will fall during a power outage and could create an unsafe environment. Down acting presses are commonly blocked at night to take pressure off of the hydraulic system. The lower beam does not move during bending so the operator will not get feedback that the brake is engaged.
Sanding is the operation of finishing wooden items after they have been machined. Essentially, a sanding machine performs a sand papering job to produce a uniformly sanded surface. Three common types of sanding machines are : Belt sander; Spindle sander; Disc sander. It has an endless cloth backed abrasive belt which runs over two drums and is used for sanding and shaping flat surfaces. One of the drums is rotated by an electric motor and serves as the driver, while the other supports the belt and keeps it in proper tension. For sanding work by the abrasive belt, the the workpiece is supported by an adjustable table that may be tilted to any desired angle.
The most common application involves gluing a coating (veneer, laminate, composite, PVC etc) onto a substratum (MDF, hardboard, plywood, hollow panels, blockwood etc). The basic configuration of the pressing line is comprised of a feed belt, an automatic press and a discharge deck. This configuration can be completed with numerous options, such as glue spreaders, polishers, automatic feeders, disk, roller or belt conveyors, automatic assembling stations, panel turners and stackers. Lines with various degrees of automation can be supplied right up to fully automatic lines that do not require direct intervention by the operator.
In practice, the workpiece is either clamped between two centers or on a face plate. Long jobs are held between the centers and turned with the help of gouge, skew chisel, parting tool, etc. Generally, the lathe is supplied together with a number of accessories for making it useful for a variety of jobs. The size of lathe woodworking machines, as in the engine lathe, is usually specified in terms of the so-called “swing” of the lathe and the maximum distance between centers.
Brushing machines are used as a labour saving tool to clean wood before other work is carried out, such as, gluing wood panels. Cramps and presses are used to assemble the wooden pieces that make up window, door or other types of frames. Dust extraction when working with wood is very important for the health of your lungs. There are several solutions, either large machines that draw the dust away. Or small bags that fit directly to the machine which sucks the sawdust straight into it, helping to cut down the amount of dust in the air. Read extra info at https://www.v-holdmachinery.com/.