High quality pcb assembly factory? Best Technology, establish on June 28, 2006, is a Hong Kong registered company whom focused on one-stop solution provider of FPC, Rigid-flex, MCPCB, FR4 PCB, Ceramic PCB, Special PCB such as Heavy Copper (up to 20 OZ), extra thin PCB (0.10, 0.15mm), and PCB assembly service. Read more info on ultra thin core pcb. Cheaper PCBs and perf boards (shown above) will be made with other materials such as epoxies or phenolics which lack the durability of FR4 but are much less expensive. You will know you are working with this type of PCB when you solder to it – they have a very distictive bad smell. These types of substrates are also typically found in low-end consumer electronics. Phenolics have a low thermal decomposition temperature which causes them to delaminate, smoke and char when the soldering iron is held too long on the board.
A single sided flexible printed circuit (1 layer flex circuit) is a flex circuit with one layer of copper trace on one substrate, and with one layer Polyimide coverlay laminated to copper trace so that only one side copper will be exposed, so that it only allowing access to copper trace from one side, comparing to dual access flex circuit which allows access from both top and bottom side of flex circuit. As there’s only one layer of copper trace, so it also named as 1 layer flexible printed circuit, or 1 layer flexible circuit, or even 1 layer FPC, or 1L FPC. The multi layer flex circuit refer to a flex circuit with more than 2 layer circuit layers. Three or more flexible conductive layers with flexible insulating layers between each one, which are interconnected by way of metallized hole through the vias/holes and plating to form a conductive path between the different layers, and external are polyimide insulating layers. Quality Policy: PCB Quality is the core of products. All of engineer & vital department guys has more than five years expenrience in PCB industry, we follow up the default PCB standard, as well as with clients’ special request.
Tg means Glass Transition Temperature. As flammability of printed circuit board (PCB) is V-0 (UL 94-V0), so if the temperature exceeds designated Tg value, the board will changed from glassy state to rubbery state and then the function of PCB will be affected. If working temperature of your product is higher than normal (130-140C), then have to use High Tg PCB material which is > 170C. and popular PCB high value are 170C, 175C, and 180C. Normally the FR4 circuit board Tg value should be at least 10-20C higher than working temperature of product. If you 130TG board, working temperature will be lower than 110C; if use 170 high TG board, then maximum working temperature should be lower than 150C.
Dust can cause damage in multiple ways. Firstly, it can reduce the heat dissipation of a device. It also contributes to damage by way of static electricity. Storing a PCB in temperatures that are not optimal can certainly lead to damage! Temperatures that are too low lead to condensation that adversely affects the PCB. Similarly, temperatures that are too high lead to warpage. If PCBs are stored in the proximity of chemical reagents, the fumes from the reagents tend to corrode the PCB. Finally, storing PCBs in a place that is infested with pests can lead to biting the PCBs and rendering them unusable.
Flex PCB ( FPC ) is stands for Flexible Printed Circuits, or sometimes we just call it Flexible Circuits or Flex Circuits, which is the electronic component developed to allow electronic goods to become smaller and lighter, and it have been widely used from 1980s in USA & Europe, and then widely spread out around the world. Since flex circuits (flexible circuit) has excellent working efficiency and strong heat-resistance, it is widely used as a core component of all electronic goods such as cameras, computers and peripheral equipments, mobile phones, video & audio units, camcorders, printers, DVD, TFT LCD, satellite equipment, military equipments, and medical instruments. Anyway, Best Technology flex pcb manufacturer will provide OEM/ODM service. Discover extra info at https://www.bstpcb.com/.
Generally speaking, aluminum is the most economic option considering thermal conductivity, rigidness, and cost. Therefore, the base/core material of normal Metal Core PCB are made of aluminum. In our company, if not special request, or notes, the metal core refer will be aluminum, then MCPCB will means Aluminum Core PCB. If you need Copper Core PCB, Steel Core PCB, or Stainless steel core PCB, you should add special notes in drawing.